Plumbing for Beginners: What You Need for Bathtub Installation

Plumbing for Beginners: What You Need for Bathtub Installation

Blog Article

Call Today

This article down below pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is incredibly insightful. Have a go and make your own personal conclusions.

Installing a bath tub isn't precisely rocket science, yet it does need strong plumbing, woodworking, and also often, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably tough job. If the old tub is conveniently obtainable, the job can relocate easily; if you need to open a wall surface to get rid of the old tub and also position the brand-new bath tub, the job is much harder. In either case, the job is within a home handyman's abilities, although you will require an assistant to move out the old bathtub as well as set in the new one. See to it you have actually certified on your own for the task and fit attempting it. As opposed to hiring a specialist to take over a halfway-completed job, it is better to consider using one prior to you begin. Opportunities are you may need a professional plumber to make tube connections.
This write-up will certainly assist you install a brand-new tub in your shower room if you have already acquired a brand-new bathtub and also do not require to transform the plan of your previous water system pipelines.
Your devices and material list must make up the following:

New Bath tub

Hammer

Pipeline Wrenches

Prybar

Safety Glasses

Degree

Pliers

Flexible Wrench

Putty Knife

Screwdriver

Cold Chisel

Tape Measure

Pipeline Caps

Removing Old Touches

If you need to replace old taps with new ones as a part of your setup, then the first thing you must do is separate the water system. After doing so, turn on the faucets to drain pipes any kind of water staying in the system. The procedure of removing the existing taps can be fairly problematic because of the limited gain access to that is often the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming during this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any old securing substance.
Before carrying on to fit the brand-new faucets, compare the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new taps to fit.

Fitting New Taps

If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the various other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the placing hole in the bath/basin ensuring that the washing machines are in area between the tap as well as the sink. Secure the faucet in place with the maker provided backnut. As soon as the tap is safely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal faucet ports. The previous kind ought to be attached to the faucet finishes first, tightening just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.

Installing the Bathtub

Making use of the two wooden boards under its feet, put the tub in the needed setting. The wooden boards are practical in uniformly spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The next goal is to make sure that the bath tub is leveled all round. This can be accomplished by examining the level as well as adjusting the feet on the tub until the level checks out level.
To install taps, fit all-time low of the furthest versatile tap adapter to the proper supply pipe by making a compression join; then do the same for the other tap.
Activate the water system and examine all joints and also brand-new pipework for leakages and also tighten them if essential. Fill up the bathtub as well as also examine the overflow outlet as well as the regular outlet for leaks.
Ultimately, deal with the bath paneling as described in the manufacturer's user's manual. Tiling as well as securing around the tub needs to wait until the bathtub has actually been utilized at least when as this will certainly resolve it right into its last placement.

Planning for the Installment

To start with, the supporting frame supplied with the bath needs to be fitted (if called for) according to the supplier's directions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to ensure that if the tap features a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps device to stop pressure on the tub.
Fit the versatile tap connectors to the bottom of the two taps utilizing 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you use every one of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be suited its last setting.

Tiling Around the Bath tub

In the area where the bath meets the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to crack a rigid seal, causing the water to penetrate the wall between the bath and the tiling, causing difficulties with wetness and also feasible leakages to the ceiling below.
You can select from a variety of coloured sealants to blend in your fixtures and installations. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly load the tub with water prior to securing, to permit the movement experienced when the bathtub remains in usage. The sealant can break rather very early if you do not take into account this motion before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also quickly offered on the market. It is a good idea to fit the floor tiles making use of waterproof or water-proof sticky as well as grout.

A Step-by-Step Guide to Installing a Bathtub

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

Remove the Existing Bathtub

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

Choose the Right Bathtub

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

Install the Plumbing and Ledger Board

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

Install the Bathtub

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

Hook up the Plumbing

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

Install the Bathtub Surround

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

We were guided to that report about Tools You Need to Install a New Bathtub from an associate on a different web address. If you enjoyed our blog entry kindly do not forget to share it. Thanks so much for your time spent reading it.

More Details

Report this page